Altigen-comm TRITON T1 Manuel d'utilisateur télécharger pdf

TRITON T1 BOARD

QUICK INSTALLATION GUIDE

MINIMUM

SYSTEM REQUIREMENTS:

• IBM/PC AT compatible system with adequate number of full-size ISA and PCI slots

• 233 Mhz Pentium processor (or better)

• 2 - 4 GB Hard Disk Drive Space (depending on voicemail requirements)

• Windows NT Server 4.0 with Service Pack 4 (or higher) installed

• 128 MB RAM

• AltiGen’s Quantum Telephony Board (one or more, Rev. D or higher)

• AltiGen’s Triton T1 Board (one or more)

• AltiWare OE R3.0 (or higher)

• 300W/10A CPU Power (minimum required to power AltiGen boards only)

• CSU (Channel Service Unit)

*** Faulty signals include the following: yellow alarm, bipolar violation or frame error

MVIP BUS

Termination Switch

MVIP Connector

TRITON T1 BOARD

System

Configuration Switch

# of AltiGen Boards # of Slots** CPU HDD

1 Triton T1, 1-3 Quantum 2 PCI, 3 ISA 233 Mhz 2GB

1 Triton T1, 1-6 Quantum 2 PCI, 6 ISA 300 Mhz 2GB

1-4 Triton T1, 1-10 Quantum 5 PCI, 10 ISA 350 Mhz 4GB

# of AltiGen Boards Power Supply** Typical Power Supply

1 Triton T1, 1-3 Quantum +12V: 4.2 Amps +5V: 6Amps 300W/30A@5V/12A@12V

1 Triton T1, 1-6 Quantum +12V: 8.4 Amps +5V: 10.8Amps 400W/40A@5V/16A@12V

1-4 Triton T1, 1-10 Quantum +12V: 14 Amps +5V: 21Amps 400W/40A@5V/16A@12V

GREEN LED RED LED Status

OFF OFF No power

ON OFF Normal operation

OFF ON No signal

ON Flashing Faulty signal with frame synchronization***

OFF Flashing Faulty signal without frame synchronization

Alternating Alternating Frame slips in normal operation

The Triton T1 Board uses the following signaling and framing features:

Signaling: loop start, ground start, E&M immediate start, E&M wink start*

Line Encoding: AMI, B8ZS*

*recommended

** The above system requirements are for AltiGen components only, and do not take into account requirements for other

system components such as motherboard, disk drives, etc.

LED Indicators

1 2 3 4

Résumé du contenu

Page 1 - TRITON T1 BOARD

TRITON T1 BOARDQUICK INSTALLATION GUIDEMINIMUMSYSTEM REQUIREMENTS:• IBM/PC AT compatible system with adequate number of full-size ISA and PCI slots• 2

Page 2 - CPU 3 2 1 0

STEP 1: MAKE SURE BOARD ID OF QUANTUM BOARD(S) IS SET PROPERLYThe first (outer-most) Quantum board ID should be set as 0, the next boardID as 1, and s

Page 3

STEP 3: CONNECT THE MVIP CABLE AND TERMINATE THE MVIP BUSSTEP 4: CONNECT CSU (CHANNEL SERVICE UNIT) TO TRITON T1 BOARDUsing Adtran’s CSU (model T1 CSU

Page 4 - AltiGen Communications, Inc

STEP 6: TURN SYSTEM ON AND INSTALL ALTIWARE OEOR START ALTIWARE OE TO CONFIGURE NEW T1 TRUNKS• End users, please contact your Authorized AltiGen Deale

Commentaires sur ces manuels

Pas de commentaire

Altigen-comm TRITON T1 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Altigen-comm TRITON T1. AltiGen comm TRITON T1 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels